STARTER COVERS Insulate your starter from intense exhaust heat Blocks excessive heat that can destroy starter and solenoid A must for vehicles with high-heat-generating exhaust headers. Withstand temperatures up to 1,000 degrees F without burning, melting or distorting. Covers are approx. 7-1/4" x 22". Select fiberglass starter cover or fiberglass with special heat-reflective aluminized outer cover. Applications: All Makes All Models

Heat Shroud Wire & Line Protector from DEI - Made from the same laminated material and offers the same benefits as the Heat Sheath with the convenience of hook & loop closure. Perfect for wires and hoses that cannot be easily removed.

Cool-Tube Wire and Line Protector from DEI - Protect wiring, fuel and brake lines, and other areas from heat up to 500 degrees F. Made from convoluted Nylon and covered with aluminized fiberglass fabric. Reduces temperatures about 43%. Covers are slit lengthwise for easy installation. Made in the USA.

Thermo-Sleeve is the combination of a high temperature fabric laminated to a highly reflective foil. It provides protection from radiant heat for hoses and wires. Thermo-Sleeve's ultra lightweight construction provides more insulation than traditional bulky rubber-coated fiberglass. The aluminized sleeve reflects more than 90% of radiant heat; it is fireproof and oil resistant.  Available in two (2) sizes:  3ft.  1/4" - 1/2" = $12.95 3ft.  5/8" - 1"   = $17.95

Exhaust Insulating Wrap is an innovative way to create more horsepower and reduce under-hood temperature. Wrapping headers with Exhaust Insulating Wrap maintains hotter exhaust gases that exit the system faster through decreased density. This produces increased exhaust scavenging - as well as lower intake temperatures. Exhaust Insulating Wrap withstands continuous heat up to 2000 degrees Fahrenheit; it contains no asbestos. Thermo-Tec's exhaust wrap will not over-insulate a system when properly installed due to a proprietary coating - Thermal-Conduction-Technology - that conducts heat across the wrap's surface. This unique coating controls heat buildup and dissipation.  Length = 50ft - low profile 1/16'' thickness - and your choice of 1" or 2" width.

Exhaust Wrap from DEI - Increase exhaust gas velocity for improved power by wrapping exhaust headers and connector pipes. This fiberglass composite material endures exhaust temperatures while keeping the heat in the pipe. Reduces underhood temperatures. This 1" wide by 50' long roll works great for wrapping tight radius bends. Use the (70305) Stainless Steel Locking Ties to hold wrap in place. Made in the USA.

MYLAR-FACED FOAM SOUND/HEAT INSULATION WITH VINYL LINING Protects against noise, vibration, heat and cold Contact adhesive sold separately High-density fire-resistant vinyl lining between layers of foam blocks sound transmission Permanent noise/temperature insulation ideal for use in engine compartment, hood, trunk and fender. Great under mats and floorboards. Acoustical-quality foam reduces airborne noise and noise from engine by absorbing vibration. Aluminized 1/2-mil. facing is attractive and easy to clean. Reflects heat and prevents absorption of dirt, fuel, oil, water, etc. Installs easily with contact adhesive (sold separately). Trims with scissors or knife for perfect fit. Instructions included. Applications: All Makes All Models

Heat and Sound Insulation from DEI - This revolutionary material adds a new dimension to control heat with minimal clearance needed, only 3/16". The Floor and Tunnel Shield is constructed using an embossed 10 mil aluminum face bonded to a 1/8" composite fiberglass insulation and is backed with an aggressive adhesive that holds past 450 degrees F. Capable of handling direct temperatures up to 1750 degrees F. Tough enough for under vehicle applications. Also blocks up to 50% of unwanted road noise. Made in the USA.

Universal Turbo Insulation Kit from DEI - Heat = Power. Keep the Heat in the Turbo where it does the most good. Reduces underhood temperatures too. This universal kit is designed to fit all turbos. Includes all materials necessary for a clean, professioanl looking installation. Made in the USA.

MSD Ignition 3412 Heat Shield Pro Boot Guard - Spark Plug Boot Sleeving, Fiberglass Sleeve